D Link 615 does not reset the settings. You can carry out this operation in two ways.

This instruction You can use to configure the D-Link DIR-300 router.

If you have already been configured by the router, you advise you before performing the following recommendations for configuring to reset to factory parameters. It is necessary to do this as follows: on the back of the router there is a reset "RESET" button, which must be closed for about 10 seconds.

1. Entrance to the router

Open the browser and in the address bar, enter 192.168.1.1/. In the "User Name" field, enter ADMIN and click the "Log In" button.

2. Update firmware

The firmware can be downloaded from the official FTP server D-Link.

Attention! The router is stitched in several stages. If you have disabled all connections, in no case disable the router power! It will turn on approximately 5-10 minutes after about 5-10 minutes.

In the router menu in the "Tools" section ( Maintenance) Select "Firmware Update" software).

Click the "Select File" button, open the folder where the firmware file is located, select it, click "Upload" (Update) and "OK".

3. Configuring Internet

Make sure the router settings match the drawings.

4. Setting up Wi-Fi

To configure a wireless network in the "Setup" section, select "Wireless Settings" (Wireless Settings), then click the "Manual Wireless Connection SETUP" button.

It is recommended to install a password on a wireless network so that no one except you can connect to your router and use the Internet.
Come up with your network and password (minimum 8 characters) and enter them into the appropriate fields. For security purposes, do not specify personal data as a password (date of birth, mobile phone number). After entering all the data, click "Save Settings".

Connect your home to the Internet is very simple and most often even cheap. However, not all Internet companies provide the setting of the router for you. Therefore, the first user, the buyer, has to independently configure the router.

In order not to have any problems in the setup, simply follow our simple instructions for setting up D-Link DIR-615.

Characteristics and appearance of the router

Regarding the characteristics of the D-Link 615, it is almost nothing to say, for all such devices are extremely similar to each other. Used 802.11n technology, built-in antennas, 4 network Port., work frequency is about 2.4 Gigahertz. Data transfer rate through a cable up to 100 megabits per second, through wireless network Up to 300 megabits per second.

On the front panel there are several, and if more accurate, 8 light bulbs performing the role of indicators:

• The first indicator "Power", this light bulb is responsible for the diet of the device, connecting to electricity.
• The indicator signed "WPS", it shows the status of this function.
• LIGHT "INTERNET". It is not difficult to guess what she answers. This is a state of connecting to the World Wide Web.
• The remaining indicators are responsible for the ports. The first of them "WLAN". This WiFi mode.
• Another 4 connections through the LAN cables.

On the side panel there is only one WPS button that can quickly connect.

On the back panel there are two special places for fastening our device to the wall. And below are different ports and buttons:

• First there are 4 local ports where you can insert a network cable for connecting a home computer directly.
• One port for connecting the Internet.
• The button located inside the opening "RESET". To press it, you need to use some kind of thin object, for example, a clip. Click this button for 7-10 seconds. After the device is restored to the factory settings.
• Power connector router. You need to insert the power cord, which the other side should be in the outlet.
• Routher power on / off key. Using this button you can restart the router.

After we have accurately learned the location of all the connectors you need and indicators, you can go to the installation of the D-Link DIR-615 router, you will execute it later later.

Installing a router in place

Choose a place that would be about in the middle of our house or apartment. This is in order to be about the same signal in different rooms. Nearby should be a socket and there must get the Internet cable.

We attach it to the wall, insert the power supply, turn using the power button, connect a laptop or computer to it via LAN port. Here there is another moment, important in further configuration. If the Internet immediately appeared on the computer, it is possible to determine which IP address from your provider.

If the Internet immediately appeared, then you have a dynamic IP address. On the WLAN wire, the provider incoming traffic is immediately redirected to you.

Questions how to connect or how to install a 615 router for Rostelecom, it should not occur because each connector meets its wire.

To make a static IP, you need to execute the D-Link ports 615 ports. Move directly to the settings of the Link. About how to open ports on the D-Link router, we will write in a separate article.

Complete configuration of Device

To begin with, immediately after connecting the router 615s to the computer, it is worth resetting the settings. So, to set up D-Link DIR-615 from the very beginning:

Reset

To reset the settings you only need to press the "Reset" button, located on the reverse side of the apparatus in the hole. Press the key for 7-10 seconds. All D-Link DIR-615 router settings will become factory. This is a particularly important step for those who bought the device after someone's use.

Also reset can be done by those who forgot the password. To put the password and the default login on the router Wi-Fi D-Link. After reconfiguration is performed.

Problems of firmware

After that, it is worth noting that on routers usually costs old version Firmware, the most ancient. You can also work with it, but it is better to take care of your nerves and forces - download the update. Download yourself new firmwareTo keep up with the whole world.

On the bottom of our device there is a serial code and a bunch of other updating information. We are interested in the line "H / W VER. :**". There should be a version of your D-Link DIR-615 router on the site of the stars. We have this K1.

Now, before entering the settings, go to the official website http://ftp.dlink.ru/pub/router/, we do everything clearly in screenshots. Here is an example update to K1.

Now we have software for our router that we needed to update. Now, in fact, learn how to flash the D-Link DIR-615 router.

To do this, you need to go to the settings to the router debugging site in the router settings, this is address 192.168.0.1 or 192.168.1.1. Enter the name and password - "Admin" is the factory settings of the router D. Now you can see the interface. The firmware version is written on top. If this is version 1.0.0, then go to "configure manually". Then "System", select "Software Update", select the file that was downloaded a bit earlier and updated the modem.

On this flashing is over.

Debugging Connections to Web

We go into the same router settings at 192.168.0.1, enter Admin / Admin, click "Login". In the updated firmware, press the advanced settings below. Then chose WAN in the list, this item is located in the "Network" block.

Press the "Add" key, thereby creating a new network connection. Here you need to enter the data that the provider provides you. Connection type, login and password must be specified in the contract, do not forget to clarify these moments from him. It is necessary for connecting to the Internet. Click "Save".

Now the Internet should appear local networkThat is, on those computers that are connected via LAN local cords.

Debugging wireless network

In the "Wi-Fi" block, we click on the general settings. All this is in the same extended settings if anyone forgot. Here you click "Enable Wireless Connection", put a tick and save. As you can see, setting up the Wi Fi router D-Link DIR-615 is a fairly simple task.

After that, in the SSID field, we enter the name of your wai fi, it will be visible to everyone. Write on english language. We choose our country, the channel is automatic and the mode is the same.

Now in the Wi-Fi block, select the security settings. In the first WiFi setting, we set WPA-PSK2. In the next field where the encryption key. This is a password from Wi-Fi. On the same tab, the answer to the question is how to change the password or how to put a password on Wi-Fi.

Now you have figured out how to configure the D-Link DIR-615 router thanks to our step-by-step instructions.

Video on the topic

Quickly you internet!

Company DOM.RU often gives its users Wi-Fi Routers from D-Link. One of the most popular - DIR-615. And the users were issued different versions This router is DIR-615 K1, DIR-615 K2 and DIR-615 R1. And they walked all with a terribly trimmed firmware from Dom.ru, which almost completely closes the possibilities of the router from the user. Therefore, I decided to lay out the instructions how to remove the firmware House.ru on the DIR-615 router and install the factory there.

Before doing something - download from the site D-Link firmware Under your hardware version of Dir'a. To do this, turn it up "upside down" and read the letters on the sticker that go after the model number. For example, K1 or K2. After that, we go to the official server of the manufacturer, swing last version To my computer and put on the root directory of the disk C: \\.
Another point is to pour the firmware on the long time you need a TFTP client. Default in Windows 7 and Windows 8 it is turned off. You can enable it in the "Control Panel" \u003e\u003e\u003e "Enable and disable Windows Components":

We put a tick "client TFTP" and press the OK button. Everything, now we are ready for further actions.

Removing the firmware DIR-615 from Dom.ru

1. Disconnect the provider cable from the router and connect with the computer. And the computer is connected to the first LAN-port DIR-615.
2. In the settings of the network card on the computer we prescribe a static IP address:

IP address - 192.168.0.2
Subnet mask - 255.255.255.0
Gateway - 192.168.0.1
The addresses of the DNS servers can not be indicated.

3. Turn off the router.

4. On the computer run command line And in it - the team: ping 192.168.0.1 -t.

5. Press the RESET button on the router or clips on the RESET button ("hole" on the back of the router) and keep it (sometimes keeping it clusted about a minute).

6. Turn on the power of the router. And look at pingie. As soon as there is a stable response without loss - let go of the button.

7. Interrupt pings using the Ctrl + C key combination and write a new command:

Press the ENTER button and look at the result. If everything is fine, the answer should be approximately as:

Successful transmission of 3345428 bytes for 12 seconds., 1334415 bytes / s

After that, the WiFi router must reboot and start with a new, factory firmware. Once again, we reset the settings by pressing the RESET button for 8-10 seconds and try to go to it through http://192.168.0.1. Username will be Admin and password - admin.

The DIR 615 router is the DLink production model, which has proven itself in the computer equipment market. The router steadily holds the network, has the capabilities of the Wi-Fi connection. It allows you to protect all home computers, while carrying out a transparent connection between them. But not everyone can rightly be able to configure everything you need, so check how simple it is.

Equipment

When buying such a device, you need to make sure that everything we need for initial work is already in the configuration. Not very nice, buying a router, bring him home and understand that now you need to go beyond the cable, because when you first turn on D Link DIR 615, the setting is carried out only by network cable. Private case Wi-Fi settings for the first time is not suitable - the network is disabled.

But in the configuration there is everything we need for the first time: wire for connecting to a computer, a pair of antennok, the power supply for the network, the device itself and the program disk. Also a whole pile paper, guarantees and most importantly - instructions in Russian. There is also a special stand: the router can be put on the edge so that he takes less space on the table.

Connect to computer

Connect is very simple. First, screw the antennas, they have the most ordinary thread, then pull out the Internet from the computer and stick it into the WAN slot to D Link DIR 615. The setting of the first connection must be carried out via cable. Next to the WAN socket, a sticker is usually located, withdraw it, behind it 4 identical ports. An attached cable connect one of the ports with a computer. Which port out of four choose - decide for yourself, now they are equal. On the computer sticking the cable at that nest, where there used to be the Internet. In connect the power supply. All we need for initial settingReady. We stick the plug into the rosette and wait until the router boots. At the same time we turn on the computer, if it was not done before.

Start setting

So, we joined the cables, turned on the computer, the router, but now there is no internet - however, on the first time it is not needed. You will need the instruction to the instructions are quite detailed, so we use it.

I turn over the pages to the Russian language (it is usually the second in the brochure) and begin to customize. First you need to inform the Internet. To do this, you will need settings issued by the provider when connected. However, if you have an Internet connection through ADSL-Modem, the settings will be greatly simplified. Now turn on the browser and drive the following numbers in the address bar: 192.168.0.1. This address router gets at the factory, perhaps we will then change it.

In the login window that is loyed, drive the necessary data. They are in the instructions, but this router they are ordinary: admin in both fields. Click "Enter" to confirm and get into main screen DIR 615. Setting all parameters is displayed here. You can configure B. semi-automatic modeWhen using the buttons on the left, but more correctly check and make all the settings yourself. We click "Extended Settings" in the lower right corner and go to the phased setting. Typically, the language picks up correctly. If no Russian has opened, it is possible to fix on the right to the right button.

Configure Internet

Immediately make a reservation that if the Internet cable is included in the modem, and not in the DIR 615, the setting is greatly simplified. The difference will be if the Internet goes through the modem, then in the router you can choose static or and the rest will pick up itself. If there is no modem, you will set up the network in the DIR 615 itself. Opens the WAN link in the "Network" block in a newly open window. Switch by reference and select the connection type. Most providers use PPPoE. Select the type of connection in the top field. Then slightly below the port and the name (it is rather necessary for you). In order for your provider to admit a router and allowed him to enter the network, sometimes you need to replace mas. We make it a little lower in the "Ethernet" section. If you have connected the router to the same network, through which they used to go to the network, click the "Clone MAC" button. In the figure below it is not signed, in this version of the firmware it is on the right of the MTU -1492 field

In the "PPP" section, enter the username, password and set the MTU value in 1492. This data represents the provider when connected, and when the MTU value is higher than the specified network, there may be problems with the network. The remaining parameters are exhibiting as in the picture below.

We wash on, in the "Miscellaneous" block set two ticks: be sure to NAT, it is also desirable to enable "Network Screen" - additional protection when working on the network. This is the same firewall or firewall, but built into the router. In the picture below they are included.

Save all the settings by clicking on "Apply". The main part is made. In the new tab of the browser, you can open, for example, search engine "Yandex".

Wi-Fi Setup

If we have a laptop or smartphone, they will be able to enter the Internet too through the router. To do this, back to the main window of the DIR 615 settings. It is produced in the block that is called. Click on " General settings"And in the window that opens, select" Enable ".

Saving changes to "change", back to the main window. Now in the same block, let's go on the link "Basic Settings". Here you need to set the name of the network (your smartphone will be seen when searching for the network). Again click "Change".

Actually, this is all if you live in a private house, Smart will catch not only next to the router. If you are in the apartment and do not want the neighbors to use your connection, you need to protect it with a password. From the main window, follow the link "Security Settings". Install the settings as indicated in the picture below. Password introduce your own. Click "Change".

Now you want to connect to your network must specify a password. It will have to specify and you, so the password needs to be saved.

Here, in fact, all that is necessary for normal operation DIR 615, wiFi Setup Performed, now on a laptop / smartphone you need to try to find new network And connect to it.

On this you can put a point. You can figure out the stand and try to put a router on the edge. We reviewed the basic parameters of the DIR 615. Setting the remaining parameters is made on the same principle and described in detail in the instructions.

Conclusion

In conclusion, let us touch the question of resetting the DIR 615 settings. He may not need you, but it is worth considering. The reset button is located on the back side of the router in the form of a small hole in the circle signed by "Reset", next to the power supply connections. When the router is enabled with a clip or pin, press it (it is in this hole) and hold for a minute. After release, the router will start a reboot, after which you can re-configure Internet, Wi-Fi and other parameters.