How to connect a wifi router if there is wired internet? How to connect and configure Wi-Fi router? Step-by-step instructions for all models

Hey! Today I will show how to connect a Wi-Fi router to anything in your home. But in the simplest case, start from the computer - it is often used, and it is more convenient to configure on a computer than on the phone. There is no special difference in the connection on the wire between the computer and the laptop - everything is equally. Let's start.

Dear reader! Are there any questions? Do not know how to solve your problem? Below this article has comments - write your story in all details, and I will give you an answer.

The algorithm for connecting the router of any model is the same - you will not have any questions. Another thing, the internal settings of the router, which change from the model to the model. For details of the setup, I recommend looking for the appropriate article under your router on our website. The same article will be the process of connecting with minor references to further actions.

Algorithm

The whole algorithm of interaction with the new router I reduced the following steps:

1. Installation - located in the apartment.
2. Connection - This is our article, we will do everything alone.
3. Setup - input to settings, Internet, Wi-Fi, passwords.

And now let's briefly run on each stage with a focus on the connection process. And for those who do not like to read, there is a cool video on the topic:

Installation

So, you unpacked a new router, it's time to determine the place in the house. Unfortunately, the radius of the router is limited, so the best option to install it is located in the middle of the apartment:

If you have one room - there are no problems. But if much - put the router and walk around the apartment with a laptop or telephone, measuring the power of the signal to have enough everywhere. Choose a better point, and in the future there will be less climb.

Another problem is to position so that the provider's cable can get to your router without destruction in the apartment. Usually when laying the Internet, the wizer can immediately say where to stretch the wire - this is done just for better signal coverage at home. But if already lies, you have to adapt to it.

Additionally, it may be necessary at this stage "Assembly" of the router - often the antennas go unscrewed, and it would be necessary to fasten them.

Connection

So they came to the topic of our article. Let's look at the rear panel of the average router in the world:

Pay attention to the 3 main places for us:

1. LAN ports are highlighted in blue, but often come yellow. The key difference is signed as LAN, and usually there are several of the same color. Ports are used to connect devices in your home LAN - computer or laptop.
2. Internet or WAN port is an external network. The cable of your provider comes here. As a rule, this port is one, and it is isolated by a separate color (in most cases blue, the drawing is selected for contrast).
3. Food. It is not confused with anything, the router is connected to the power supply. There is still a separate button to turn on, if it is, do not forget to turn on.

The final connection scheme:

1. Turn on food
2. Connect WAN
3. Connect LAN

Step 1 - Nutrition

All stages are very simple, this is no exception. We turn on the plug into the power socket on the router and connect the adapter itself to the power supply. At least some indicators should be on the router (usually flashing nutright and wifi).

If nothing burns - check the availability of current. Maybe well connected? Exactly there? Is it turned on by a network filter if it is? And most interestingly - maybe there is also a router's switching button from behind? Do not forget to turn on and her.

After this stage, the router must "come." Getting further connected.

Step 2 - Provider

If you do not need the Internet on the router - you can skip step. But usually he is just needed. We remember that for this there is a special socket - WAN or Internet. Connect you need there!

If connect to the portLAN - Internet will not! But there are exceptional models where it is permissible.

After connecting this wire, another external network indicator usually lights up.

Step 3 - Computer

Now connect the computer itself (in the general case and laptop) on the wire. We take patch cord - the same network cable that comes in a set with a router (if not - running to the store). One end sticking in the LAN port of the router, the other - to the network card on the computer.

It will not be difficult to find - all ports look equally, because Go one standard - RJ-45:

The same is usually present on laptops. After connecting on the router, the last indicator that interests us is the lan network.

If you have a fewLAN ports - you can connect to any of them. No difference.

As a result, the ports must be clogged approximately like this:

It is very difficult to make mistakes. Must do everything right from the first time. Everything! You do not need anything else to connect here, and you can go to the setting.

There is another way to connect to the router - throughWi-Fi. Just choose our active networks in the list, enter the password and that's it. The network name and password usually write on the sticker under the bottom.

Setup - very brief

Why is very brief? Yes, because the configuration process itself varies from the router to the router. So if something is incomprehensible - write in the comment, and it is better to go to the article about the configuration of your model of the router on our website - there will be everything in detail and with all the nuances. Below I give a universal algorithm for all models.

Step 1 - Log in to the panel

First you need to log in to the web configurator. The best way is to look at the router and show the actual data to enter the control panel, login and password on the sticker. It looks like this:

If nothing helps, go to the following links, one of them should appear the login and password input window:

192.168.0.1
192.168.1.1

Login and password look at the same sticker, but usually they are standard not everywhere everywhere admin. and admin..

Step 2 - Internet Configuration

And here begin great discrepancies. As they got into the configuration, look for a setup wizard. He will hold you on the steps and will confuse everything. What is important here - to find a contract with your provider, where the login and password go from the Internet itself. During the setup process, you will have to drive them here. As a result, the router must connect to the Internet.

Step 3 - Setting up Wi-Fi

If you use the setup wizard - you will also go through this stage. The main thing here is to set the name of your Wi-Fi network - do it understandable for yourself. And it is very important - change the password to the wireless network so that no neighbor can connect.

Step 4 - Password from Routher

And at the end of the entire setting it is very important not to forget to change the password itself on the router (well, which is the same admin.) - So we will reach our apartment from the ingenic intervention of evil hackers, and we will live happily ever after.

That's all! You will not think about anything else. Details need to look more specifically under your model or simply ask a question in the comments below. Be sure to answer!

As soon as the user, in addition to the computer, begins to use another gadget to use the World Wide Web, then he immediately arises the problem of providing it with access to the Internet and at the same time not to carry additional communication costs. But, more often than domestic devices with the surfing function in the global network, even more than a few. To optimally solve the problem, as a rule, a device distributing Internet, i.e., routing it to all available houses Computers and gadgets.

However, one of the acquisition in the store of this device does not solve the problem, and it is still necessary to know how to correctly connect the router. Below, simple words with the drawings, a detailed description of all actions, how to connect a router to a computer using Wi-Fi or Patch Cord cable for a router, as well as how to connect a wireless router, so that everything works well, and as they say well - Wi-infant, making an available Internet where it is necessary.

In order to eliminate often emerging difficulties at the end, a manual on how to correctly connect the router to the router and configure them. The outlined instructions are equally applicable for any models of wireless and wired access points.

The essence of the work of the device

Before proceeding directly to the issue of connecting the device, you need to know the basic principle of its functioning. Experienced users can simply skip this section of the manual and immediately go to the next one.

The router is an instrument that independently performing a connection with the global network using the parameters entered into its interface, in fact, this small-sized device performs the role of a computer, but with the routing function, so the router can distribute the Internet to a plurality of devices through Wi-Fi or by cables.

Physically, the router itself is connected to the worldwide network, the router is assigned a certain IP address. Therefore, it is not necessary to pay additionally computers or smartphones connected to it or smartphones, of course, if additional services were not purchased.

Connection procedure

The connection of the WiFi router itself is very simple, and have a significant amount of knowledge for this not necessarily. On the case of all routers there is a special "Internet" jack, where it is required to connect the wire from the communication service provider (this connector is called "WAN").

Nearby there are "LAN" connectors, it is precisely one of them to connect a patch cord to the PC network card or a laptop. And through these ports, wired communication is carried out with various consoles, smartnes, additional computers, etc., which for the house also play an important role.

Now step by step will analyze the questioned how to connect the router. It will be necessary to produce only a few consecutive steps:

1. Insert the wire from the provider into the "WAN" connector;
2. Going in a set by the Wire to perform the connection of any of the connector of the router with the same Nest of the PC network card;
3. To submit electricity to the device through a complete adapter, connecting it to the network 220 V. Then, if there is, by pressing the "On" key On the router housing, activate the device (there will be special indicators on its enclosure);
4. Ready! The router is connected. It remains only to enter the necessary settings.

The router is connected to further configuration, accessible and without a cable connection with a PC, and connecting with it via Wi-Fi. But it is a less reliable method. Especially when it is done by the newcomer, after the introduction of the parameters, already reappearing, it is often emerging. Of course, they can quickly be eliminated, however, in case of insufficient experience of the owner of the apparatus, the correction will require considerable costs of nerves and time. Therefore, it is strongly recommended to enter the settings to use a wired compound.

Connection procedure "ADSL" router

The principle of actions is fully similar to the described algorithm of the previous section of this instruction, but in this router the WAN port is missing and it replaces the connector with the name "Line". After connection, you can immediately start using the ADSL Wi-Fi router settings.

How to connect a router on the router?

If you need to cover a large area of \u200b\u200bthe coverage of the wireless signal, for example, in the case of a large apartment or at home, it is effectively connected by the router to the router. This is guaranteed to increase the radius of the WiFay coating radius.

Schematically, this can be shown as follows:

There are 2 main methods for implementing the task:

1. Using cable;
2. Via wi-fi.

1 Method: Wired

A cable referred to as a twisted pair that has sufficient length to connect 2 routers among themselves.

In order to connect, it is necessary to make the following actions:

1. One end of the wire in the LAN jack of the router connected to the global network;
2. Another cable plug insert into the "WAN" connector of the 2nd router;
3. Next, enter settings in the 1st router to configure the Internet provider, and in the 2nd dynamic IP.

2 Method: Vi-Fi

If there is no possibility of pulling the wire between the devices (which is extremely often found), you will have to use the second technique, which is characterized by the complexity of the settings, so it will pay more attention in this guide.

The user has access to the router with access to the global web (we denote this router "1st") and another device for use in the repeater function - "2nd".

At the first stage, you need to connect the "1st" from the PC and perform the Internet settings on it. Then connect the "2nd" from the PC and perform the connection settings to the access point.

The actions algorithm includes the following sequential steps (provided for Windows operating system 7, but the algorithm is completely similar to, with minor changes, for other versions of Windows):

How to install and connect Wi-Fi wireless router Today, people are increasingly interested in people who want to get freedom of action and feel comfortable and independent of the wires work at the computer. I think you will agree with me that leading your online business or just walk through the Internet spaces is very convenient if there is freedom from the wires and the ability to move around the house and office. I think you, like me, with two hands for a comfortable and convenient organization of your workplace.

It does not matter whether you will be retrieved income from the Internet resource or provide consulting services, conduct an online store, create various kinds of services, and can simply spend time on the Internet in order to accumulate useful information, in any case, comfort creates a platform for fruitful work In any field of activity. The data rate of the router in the Wi-Fi wireless network, directly depends on the signal quality, the power of the antennas and the number of connected devices.

To signal in the Wi-Fi wireless network, it is stable and strong, you need to in the building (apartment, house, office). It should be said that in this publication, we will consider connecting the hardware of the Wi-Fi router, and how to configure the Internet access on the router and configure the wireless network on it.

I draw your attention to what is very often not aware, users buy a wired router instead of wireless. What are their differences? The fact is that Wi-Fi router (it is also wireless) makes it possible to create a local (LAN) and wireless network (Wi-Fi).

That you mean the Internet, it can transmit to customers (tablet, laptop, smart TV, telephone ...) both by wires and via Wi-Fi radio channel. But with a wired router, you are waiting for only the same network of the same name. That is, using such a network device you can create only a wired local network. However, such network devices become less and almost all routers have a wireless network function.

So, closer to business. Typically, the router is equipped with a power adapter, an Ethernet cable, installation CD and quick installation manual. First of all, find a suitable place for your Wi-Fi router so that various external factors do not affect its signal. If you need to perform the diagnostics of your wireless network, find and go to a less downloaded channel, then I wrote this in this.

Connecting the hardware of the router.

First, disconnect the computer and the router from the network if you are connected. Next, you need to install the router to the optimal location so that all the wireless network participants receive a good Wi-Fi signal. In most cases, it is the central placement of the network device on the plot where wireless clients are connected by Wi-Fi connection.

Now connect all devices clients (computer, laptop, switch / hub ...) to LAN ports of the router. If you are to carry out the wireless connection of customer devices to the router, then this step will skip. That you do not need any wired connection.

In the image below, I sketchically displayed how to connect the router to devices and to the Internet.

When connecting a Wi-Fi router to a computer and subsequent network device setting, usually use the patch cord. For this, just need patch cord in one end to stick into one of the ports of LAN (1, 2, 3, 4) of the router, and the other in the network card (Ethernet port). If for any reason it is missing, you can yourself.

After connecting and executing all the necessary wireless settings, this computer can already be associated with the router not using a cable, but via Wi-Fi.

It remains only to connect the cable from the Internet provider in the WAN port of the router, connect the power adapter to it and turn it on into the outlet. The router will automatically start its download.

Now enable your computer and check the physical connection to the device router using the indicators. In the manual for your router or on the installation disk, the status and value of the indicators should be described. In my case, the description of the indicators looks like this:

If the physically router is connected correctly and everything works properly, you can move to the configuration of the computer (define the type and connection to the provider) and the router. Read more about this in the second part of the article (reference at the end of this post).

Some digital can be connected using the WINCE 2001 universal wireless adapter, which software is automatically connected to the Wi-Fi router. Details about what WinCe 2001 will tell you this video clip.

In the conclusion of the article I want to draw your attention to the fact that the router in some cases, like a computer, to avoid failure, as a result of landing and a voltage burst, it is better to connect to the power grid through an uninterrupted power supply. In addition, the UPS will give you the opportunity to finish your work at a computer without losing data.

Now you know how to install and connect a wireless router. Until!

2014-08-31t15: 27: 44 + 00: 00

Alexey: You can configure through the tablet, on Wi-Fi wireless network. Although I am a supporter of the router setting through the patch cord, through a computer.

2014-08-30T23: 20: 07 + 00: 00

Rustem: You can use it, but to configure the router PC you will still need.

2014-08-30T23: 18: 09 + 00: 00

Antonk: Connecting the router via the UPS is relevant when the hard disk is connected to the router. This will avoid the occurrence of errors on the screw.

Currently, there is a huge range of various routers from a variety of manufacturers. We long view all sorts of notes on the network about certain brands and models of routers to maximize benefit from the purchase.

When the time of preparation of the purchased router is coming to work, i.e. Connecting it to the network, device and subsequent configuration, then we begin to scatter your eyes and make thoughts. The thing is that the first router setting is not the easiest task, which is due to multiple factors: the frightening number of different connectors on the case, the installation, the installation, device setting, etc.

In this article, we will present detailed instructions for installing and configuring the router, which you can use with any model from any manufacturer. In the end, they do not differ much among themselves. So, let's begin.

First, let's go through some items that will be useful to know everyone who is going to connect the router for the first time. First, the principle of connection in all routers is the same, i.e. It doesn't matter what model and from which manufacturer you purchased is absolutely not important. Secondly, it is also not important, the services of which provider you use.

The only thing that you should worry is the type of your Internet connection with which you will work when setting up a router, but about this later in the instructions. So, let's approximately make your plan for the first installation of the router for its use:

• The first of your barrier to use the router will be its packaging, with which we hope you will not have problems. Getting rid of packaging, then you need to connect the device to the computer you need, and then connect both cable to them, i.e. Power adapter, Internet provider cable, a power cable between the router and computer.
• As soon as you can spend all this bunch of wires between the computer and the router, and then save it, you will need to go to the settings. This is done in all cases equally using a special IP address and browser. We enter the browser to the address bar specified on the router box the IP address and the page with its settings will open. Everything is quite simple here.
• Having passed in the router settings, you will need to set the required parameters in it. Running a little forward, you will set the connection type of your Internet in the settings, as well as personal data from it if it is required, but about this more further in the instructions.
• And the last thing will remain - this is an exhibition for your already configured Wi-Fi network preferred name and password. You can use both factory values, but it will be better to put your own.

As you can see, everything is not difficult ... relative. Most users still have certain difficulties during the implementation of the above actions. Let's go through them in more detail.

Installing a router for work

First you need to decide on the place where the router will be located. But, you will not have to choose to choose to you, as this place will be the location of your Internet provider cable. In general, repel from the circumstances. However, it is recommended to still install a router higher.

Next, you need to connect the router to power using the adapter. You will immediately understand that he started working on tanned indicators on it. If they do not burn, then you probably have a power button on the router - click on it.

Now you need to scatter the desired cable for the router. If you connect the router to the computer, then you need to first connect the cable from the Internet provider to the WAN port (usually stands out in one color on the device, usually blue or black). Then take the standard network cable that should have been in the box with a router, connect one end to the LAN port of your computer, and the other end is one of the four LAN ports of the router.

If you do not want to connect a router to a computer or you do not have such an opportunity, then you only need to raise it to meals and connect the cable from the Internet provider.

If you have done everything according to the above steps, then your router has already had to create a Wi-Fi wireless access point. However, this connection will perform under the standard name and password, which must be specified on the box or the case of the device itself.

To connect to the created network from any device with a Wi-Fi module on board, you need to activate this module and enter the password and login specified by the manufacturer.

Login to the web interface of the installed router

To configure the installed router, you need to enter its web interface, which is just the same and all sorts of settings for this device will be contained. All you need to do is drive it into the address field of your browser specified on the Box of the router or its enclosure IP address, for example, 192.168.1.1 and go over it.

I also want to point out that you do not need to already have a network connection in order to go to this address, i.e. The setting can be done without connecting to the network.

The only thing you really need to configure is connected to the router through the cable computer or device that has completed the input to the Wi-Fi network created by the router.

So, you found the address you need to enter the router's web interface. You must appear the screen with login and password. As it was already indicated earlier, finding this data will not work on the box of the router or on it itself. It is also worth indicating that in some cases the user will not even have to enter anything, i.e. The router will not be protected and it will be possible to install your username and password.

Configure the router via the web interface

Here you are inside the settings of your router. To be honest, first hitting there, you will probably be confused, due to the presence of a huge number of tabs in the web interface and settings that are located in these tabs.

However, it is not necessary to worry, as practically in any router from any manufacturer has a special option - fast setting. It may look different, but it's the meaning of her one and the same - to produce as quickly as possible and simple for the user to configure the device.

You can find this item on the web interface start page or in one of the tabs. For example, in the router from the manufacturer Netis (yes, not the most popular brand of routers, but also comes out) the quick setting can be made immediately on the start page. Here is a web interface screenshot Netis:

As you can see, you just need to check the box opposite one of the types of Internet connection and drive some data (if necessary) to the right fields. If you need more detailed settings, then click on the section Advance., and if simplified again - Quick Setup.. On a quick setup page, you will have the ability to change the login and password for the distributed network router.

Immediately you need to specify that the web interface of each router model will differ, but this should not be a problem, since the principle of setting up these devices is the same. To begin with, use fast setup, and then when you need - use advanced.

Setting up a network connection

Well, we came to one of the most complex parts of this topic - setting up a network connection for the router. If most of the most time everything was fine and understandable, then at this moment many users are really lost.

Fast setting In most cases can automatically set everything as needed, but sometimes you may need to produce manual settings. So, first, you need to know what type of connection you use: DHCP, STATIC IP, PPPOE or other. You can find this information by contacting your provider or learn it from the contract that you should have.

In most cases, providers prefer to use DHCP or dynamic IP. If you also use such a connection type, your router must already work perfectly, as it is configured in advance to work with a DHCP connection.

If you do not have access to the network, then in your case a different connection type is used. Describe steps to configure other connection types is not the simplest task due to the difference in the web interfaces of routers from different manufacturers. But let's still consider an example of configuring a PPPoe connection in the router from the same Netis:

As you can see, you just need to go to the network tab, then select under the WAN tab. In these settings, click on the drop-down menu of the connection type and select PPPoE. Then to enter a login and password from your Internet connection and everything will be ready.

Everything is intuitive and understandable if there is knowledge about the type of connection and the data for its configuration. So, in the end, you should have the following: Connected the router, chose the desired type of connection and configured this connection, i.e. Entered the desired login and password (if required), etc. If you did everything right, then your router will start to distribute Wi-Fi and you can easily join her.

Changing name, password and Wi-Fi region

Everything works, you have access to the network and everything is literally wonderful. But, the last step remains in setting up your router - this is a change in the standard Wi-Fi network name, the password change for it (the saving of the factory password is not the best solution) and the establishment of the desired region.

Again, web interfaces differ, but you must find all the above settings in the wireless network item. However, you need to clarify something about the name of the network - it will be possible to set it in the SSID field. Password, respectively, is set in the line of the same name. Register according to your location, for example, if you live in Russia, then select the EU region.

Finally

Configuring the router, though it may seem like the most difficult number of actions, but in fact everything is incredibly easy. So, let's briefly go through what you need to do:

• Install the router at a convenient place for you with an Internet connection cable.
• Connect the provider cable to the WAN port, then connect one end of the network cable to one of the four LAN ports on the router, and the other in the LAN-port of the network card of your computer. If you do not connect the cable - only in the WAN port.
• Enter the router web interface via a computer browser or using another Wi-Fi device.
• Run the setting according to your connection type.

Here, in fact, all. If you did not succeed in the first attempt to properly configure your router, it was not trouble, since it can always be reset and attempt to set up again.

Found a typo? Highlight the text and press Ctrl + Enter

Each of us came across the situation when a router must be connected in the apartment. For this, a specialist is usually called. We offer instructions how to connect the router yourself.

1. Connect the wires

Insert the Internet cable to the router's WAN port (or internet) (router).

Then plug the router to the computer: one end of the cable to the LAN port of the router, and the second is in the PC network card connector. Instead of a cable, you can use a wireless connection, but at the setup stage it is better not to do.

Connect the router to the outlet. If it has another power button, then click on it. Wait a few minutes so that the router can boot.

2. Check the Internet operation

If your router is already configured by the provider or received the settings automatically, the Internet can earn a few seconds after connecting the router to the PC.

To check this, run the browser and open several sites. If they are loaded without problems, you can skip the fourth item.

3. Routher Settings Menu

In the browser's address bar, dial 192.168.1.1 or 192.168.0.1 and press ENTER. One of these IP addresses will send in the router settings menu. If both options are not triggered, find the right IP address in the documentation for your router model and try entering it.

When in the browser window, the entry page in the settings is floating, the system can ask the username and password. Most often, during the first connection for both fields, one word is suitable - admin. Sometimes for a standard password, router manufacturers use a combination of 1234.

You can also find information for entering the instructions for the router or on the provider's website.

4. Configure Internet connection

If the Internet does not work, the router needs special settings. What parameters you need depends on the device model and Internet service provider. Unfortunately, there is no universal configuration. To get instructions, check the provider's website or ask her to support the support service.

When you get a guide to setting up your model, follow all the steps. If you are configured to connect to the Internet, and the Wi-Fi home network, you can move to the next - fifth point.

5. Adjust the Wi-Fi home network

Select the correct security settings to protect Wi-Fi network.

In the Settings menu, select the section that is responsible for the wireless network (see the documentation for your router model). Here enter a reliable password (it will be approached to connect your devices to the Wi-Fi router) and select WPA2-PSK as a means of protection.

Save settings.

6. Change the password to enter the router settings

Just in case, it is worth limiting access to the settings menu of the router. If the router is protected by a standard password, replace it with your own.

Find the settings section that is responsible for security (see the documentation for your router model) device, and enter a new reliable password. Save the changes.

If your computer has a Wi-Fi module, after the setting is completed, the network cable can be pulled out from the PC and connect to the wireless connection router.

7. Optimal router location

It is best if the router is located in the center of the zone in which you use Wi-Fi. Thus, the signal will be equally accessible to all connected devices.

By material Lifehacker