Buggy mouse button What to do. The mouse does not respond to clicks: troubleshooting. Elimination of technical faults

Sometimes users face a problem when the mouse does not react to clicks. Why can it happen? How is it suggested to deal with the task? What features and the nuances of the process are recommended to pay attention? Sometimes factors are not at all associated with information, capable of providing their influence on the mouse. Users can immediately attribute defective equipment to system administrators for diagnosis. This is a logical solution, but do not hurry. You can independently understand why the mouse does not always respond to clicks, and even without any assistance to cope with problems.

Rubbish

The first and fairly common cause of the studied phenomenon can be a banal clogging of equipment. If the mouse reacts badly to the click or does it once, it is recommended to check its purity.

Eliminate clogging can be excluded only on new equipment. If the device has worked for some time, then with the problems with the mouse you can do the cleaning component. Make it is not so hard. The result will not make himself wait, after how the user will remove all the dirt, accumulated under the buttons, the mouse will work in full force.

Fault

But this is only one version of the development of events. In fact, possible layouts are very much. Mouse does not react to clicks? It is likely that the equipment is in a faulty state. Actually for any devices - both new and already working for a while.

Faulty equipment is recommended to be attributed to the service center. There the masters will check the device and say whether it is subject to repair. If so, you can leave the mouse in the service center before troubleshooting. Otherwise, you will have to fully change the input device.

Checking performance

If a new or already purified dirt and dust mouse does not react to clicks, you can independently check its performance. To do this, it is recommended to connect the device to another computer, install hardware drivers and make sure everything works.

This technique allows you to apply visits to service centers with specific complaints. Also, with such a check, you can understand often sources of problems and failures. What other options for developing events are possible? What should pay attention to this or that?

Nests and connectors

Mouse does not react to clicks? What to do? To begin with - do not panic. This problem is found in many users, often the source of the trouble is a purely technical component, no danger for a computer or operating system does not bear it.

Alternatively, the damaged connector can be the cause of problems with the mouse. The nest to which the equipment is connected, damaged, as a result of which the contact between the machine and the manipulator is set only.

The output here is one - connect the mouse to another nest. Only it will be possible to eliminate the problem. By the way, the connection connector on the device can also be damaged. In this situation, it is better to purchase a new mouse. After all, the repairs are usually not subject to repair. Either after these manipulations, they still break, and very quickly.

Drivers

How to be if the mouse does not react to clicks or does it once? Event development options are very much. It has already been said that often all problems are precisely technical. But there are exceptions.

For example, the following alignment is characteristic of gaming mice. It's all about drivers. This software is responsible for recognizing devices in the operating system. The old version or complete lack of application data is capable of leading that the mice will work in times. Either generally will be among the unknown computer computer.

In this case, you just need to install the drivers on your computer (usually they are attached to the mouse) or update already available. After that, the operating system reboots. Is there progress? Then you can not worry. Mouse still does not fully work fully? You need to look for the source of the problem further. Alternatives still a lot.

Touchpad

Only the owners of laptops are faced with such a problem. The mouse does not always respond to clicks or does not work at all, although there is a cursor? You can try to check the operation of the touchpad. If it functions normally, it is recommended to disable this component.

The thing is that some laptops and assembly of operating systems do not support the simultaneous operation of the touchpad and mouse. Therefore, the equipment conflict arises. As a result, the mouse refuses to work normally.

As soon as the touchpad turns out to be disconnected, the performance of the connected device will return to the fullest. And it will be possible to continue to use the mouse. By the way, you should not be surprised if the problem arose suddenly - no one is insured from this.

CPU

But if the mouse does not immediately react to clicks, then the problem may be different. For example, a slow response from information is sometimes explained by the high processor load.

Why does such a phenomenon observe on computers? There are a lot of options. Among the most common allocate the following:

• a large number of functioning programs;
• non-compliance with the computer system requirements of the operating system;
• viruses;
• long operation of equipment without shutting down or reboot;
• lack of hard disk space for normal operation OS.

In any case, you need to provide the processor unloading. It is recommended to close numerous programs running in the background, as well as restart the car. It is better to give her a few hours to rest. Next, the user must resume the mouse connection attempt. The problem should disappear.

Viruses

Mouse does not react to clicks? The virus, as already mentioned, is the wave of a real reason for the emerging problem with the equipment. Any computer "infection" can lead to this phenomenon.

How to be in this case? You need to try to cure a computer. If the problem is observed on a laptop, saves the touchpad. With it, you can easily manage the computer and cursor. The antivirus system will find and cure potentially dangerous files. If you could not do this, the user will be prompted to delete the document.

As a rule, when the cursor does not work at all, the computer is attributed to the service center. There quickly the system will be cured of all viruses, without having any damage to the owner.

Incompatibility

If the mouse does not react to clicks, you should pay attention to system requirements. The fact is that all modern equipment has certain requests to the computer. Missing it makes it impossible to work the device. Either it will function unstable.

When incompatibility is detected with the operating system, you can solve a problem with several paths. Or the user changes the OS, or the plug-in equipment. The second option is most often found in practice. Particular attention is recommended to give the compatibility issues to the owners of Windows 10. With this operating system, there are a lot of equipment conflict. Therefore, wonder that Windows does not respond to the clicks of the mouse, no need.

What to do in this situation? It has already been said: or the connected equipment to change, or the operating system is changed. What exactly? This is everyone decides for himself.

Power Supply

This last reason why the mouse connected to the computer does not respond. All fault power settings. Most often occurs this problem on laptops.

As practice shows, after that the operation of the mouse is settled. In fact, everything is not so difficult. It is enough to go through all possible options. Only it will work out 100% understand what is the matter. Hurry up with the acquisition of new equipment is also not worth it. It is likely that you can do without it.

If the user doubts his abilities, the computer can be attributed along with faulty equipment to the service center. There will help not only diagnose, but also to fix any computer problem. What exactly? The final solution always remains for the user!

Users often encounter problems that occur when working with a computer. One of these problems - the computer mouse stops working. What could be the cause of a malfunction, we will analyze in the article.

Types of mice

Computer mice can be classified according to such criteria.

Causes of trouble

The reasons for which the cursor does not move and the computer mouse stopped working quite a lot, but can be divided into two groups: hardware and software.

To the hardware we will take:

To programmatically, we will take:

1. Faults associated with the device driver.
2. Intentional disabling mouse with malicious programs.
3. Conflict utilities for the mouse with another software.
4. The fault of the operating system, which created a chain of problems, which led to the inoperability of the device.

Trouble-shooting

Before making any serious troubleshooting steps, check:

Important! If the device is not identified (the device descriptor failure failure) or your mouse is in the "Other Devices" section, the problem solving is described in detail in this.

Wired

If you checked the software manipulator, and when connected, the cursor does not move or moves with failures - the problem in the hardware device. To eliminate:

Wireless with a USB transmitter

If you have a wireless mouse connected to a PC via the transmitter, go through and read the publication about. Nothing helped? Try the following:

Important! Software installed for another product (mouse, wireless keyboard, touchpad, sensor) can cause a conflict in working with a wireless mouse. We recommend removing utilities, restart the computer and check the work of the manipulator.

Bluetooth

If you use a Bluetooth manipulator and the cursor stopped working:

1. Turn off, replace the batteries and turn on the device.
2. Check the operation of the transceiver (restart it, connect another device to Bluetooth).
3. Check the driver for the Bluetooth transmitter.
4. If necessary, roll back to the previous version or reinstall the driver.

Wi-Fi

If the Wi-Fi mouse cursor stopped working or began to "twitch", the reason is possible in the protocol that the router uses. This is caused by the fact that the device and router work in the same range of 2.4 GHz. To solve this problem without replacing the mouse:

1. Go to the router settings in the Wi-Fi section.
2. Change the protocol for 802.11g, and save the changes (experiment on D-Link DIR-615M).
3. Restart the router and turn off / turn on the mouse.

Important! The change in the protocol is suitable if the speed of the Internet is not higher than 25 Mbps.

Touchpad

First of all, check whether the touchpad on the laptop is enabled. We recommend getting acquainted with the information about setting the touchpad on this.

The touchpad can be disabled software. Go to BIOS:

If the inclusion does not help and everything is in order with the driver, it means a malfunction in the hardware. It can be:

• damage to the touch panel;
• disconnecting the loop.

Tip! If you are confident in your abilities - you can check the touchpad loop fastening. It happens that during transportation it pops up from connecting connector to the motherboard.

If the tips of the article did not help detect the mouse connection problem ,. Describe your fault in the items, we will try to find the answer together.

If the mouse connects to the system unit through the PS / 2 connector (the round socket on the rear panel, next to which there is an image of the mouse), it is impossible to connect and disconnect the "hot" method, i.e. With the computer enabled. A short circuit can occur to which the PS / 2 ports are very sensitive.

If you see that the cursor does not move and the system does not respond to pressing the mouse keys, turn off the computer using the keyboard. To call the Start menu, press Ctrl + Esc or Win. Keys "Down Arrow" and ENTER Select the "Shutdown" command and confirm a shutdown request by clicking OK.

Disconnect the wire of the mouse from the port and carefully, trying not to bend the pins of the electrodes, connect again - perhaps the problem is in the absence of contact. Turn on the computer. If the mouse earned, then you did everything right.

USB ports are designed for hot connecting. However, if the mouse connected via USB does not work, still turn off the system unit before

If the problem remains, check the mouse on another computer. If the cursor moves and the keys work, it is possible that the port is defective on your system block or there are problems with software.

To reveal the source of troubles, connect to the computer knowingly good mice through PS / 2 and USB ports. It is usually not required to install special drivers - the standard Windows utilities are also suitable. If no device does not work - most likely, the problem with software.

Using the Win keys, direction arrow, Tab and ENTER, go to the "Control Panel" menu, activate the "System" icon in the "Equipment" tab, click "Device Manager", then expand the "Mouse and Other Claimers" list . A combination of SHIFT + F10 Call the context menu and select the Delete command, then reboot. The system by finding a new device will re-establish drivers on it.

If you have connected new equipment or installed a new program, the reason may be in a hardware conflict. Go to the system in safe mode when it is loaded in a minimum configuration. To do this, restart the computer and press F8 after a short beep. In the download modes menu, select "Safe Mode". At the request of the system to continue in this mode, answer "yes." If the mouse works fine, delete new equipment and software. Load in normal mode.

If the "Restore System" option is enabled on your system, try selecting "Loading the last successful configuration" in the Mode Selection menu. The system will suggest you to download multiple system recovery points. Choose the closest by the time the problems began. If the attempt failed, try another date.

Sign in the system restore mode can be different. When rebooting, choose the "Safe Mode" option, however, to answer the question of the program to continue the work. After that, you will be prompted to choose a recovery point.

In OS Windows built-in "troubleshooting means". To run it, go to the control panel using the keyboard, and open the mouse icon. Go to the "Equipment" tab using SHIFT + TAB and click "Diagnostics". To start the diagnostics, use the "Next" button. To select an answer option to system questions, click Shift. Perhaps as a result, it will be possible to find out the cause of inoperability.

If these methods did not help, check your computer to viruses. Download the free AVZ4 program and deploy it on the flash drive. Press Win + R and enter the F: \\ AVZ4 \\ AVZ.exe command to the "Open" window, where f: - the name of the removable disk in the system. Run the scan.

If the mouse works, but from time to time it hangs, right-click on the free place on the screen, select the "Properties" option and go to the "Parameters" tab. Click "Advanced" and select the Diagnostics tab. Displays the "hardware acceleration" engine to one division to the left and confirm by clicking OK.

Regardless of what type of manipulator is used, sometimes problems may occur due to the fact that the mouse cursor does not move, and the mouse works. What are the reasons and how to eliminate the consequences of the problem, read further.

Mouse cursor does not move, but the mouse works: reasons

Getting started to consider the reasons, it is necessary to emphasize on the separation of these devices by type. The easiest way to eliminate the problems of things is when standard devices connected to computers and laptops are used by a special plug or via USB ports.

In the case of wireless manipulators or non-standard models intended for games, the reasons are the mouse buttons work, and the cursor does not move, it can be much more.

However, among the most common problems, the following can be noted:

• surface pollution;
• incorrect connection or power on the device;
• incompatibility and other problems with the USB port;
• incorrectly installed, missing or outdated drivers;
• impact of viruses.

Does not move the mouse cursor, but the mouse works: what to do first?

In the simplest case, first, it is necessary to view the lower surface of the device. If there are contaminants on the bottom side, they need to be removed. Very often, because of this, it is impossible to make any action with moving the cursor on the screen.

In some cases, when the mouse cursor does not move, but the mouse works, the problem may be associated with a short-term software failure. In this case, you can try to reanimate the mouse with the usual reboot of the entire system. Note that in the case of the presence of an inoperative BIOS device warning signals does not issue.

In the case of wireless devices, the problem is that the mouse cursor does not move, but the mouse works may be related to an unchargeable battery. It must be replaced. Another reason is the incorrect turning on the device. In many manipulators, in addition to including a special button or power slider on the bottom surface (from the back side), you still need to click on the left mouse button (this also applies to the sleep mode into which the manipulator is switched when the computer or laptop is turned off). For Bluetooth devices, make sure that the corresponding module is active. For Wi-Fi, it may sometimes be necessary to enter the router and change the protocol for 802.11g.

Sometimes the reason that the mouse cursor does not move, but the mouse works may consist that it is not connected to that USB port. As a rule, on any modern computer or laptop there are several such USB 2.0 and 3.0 standards connectors. This also needs to be considered.

Finally, check the performance of a device of any type can be completely simple if you connect it to another computer terminal. If it works, then the problem is in the user system. Otherwise, the main problem can be drivers.

Change Driver

For standard devices, the driver system installs independently. But for some gaming mice, they are supplied with the manipulators themselves, and you need to install them manually. In such a situation, the drivers must be reinstalling or updated. But what to do - because the cursor does not move?

But here we will use knowledge of entering commands and use the switching between different functions, applications and sections of the system using the keyboard. To address the Device Manager, you need to use the Console Console (Win + R), in which the devmgmt.msc command is entered, after which the movement is already in the dispatcher itself using the arrow and tab buttons. You can also use the Start menu, opened by the WIN key. Calling functions and confirmation in the form of pressing the buttons is made by the input key, and the ESC key is sometimes used to cancel action.

When reinstalling the driver, the system will need to specify its location (removable media or folder on the hard disk), and not use the recommended installation from the Windows database. At the end of the driver integration, the system is desirable to restart, although it is not always required.

Conclusion

It remains to say that it is necessary to look for the cause solely with regard to a certain type of device. But in most cases, if the mouse cursor does not move, but the mouse works, and the problem is not related to software failures or physical breakdown of the mouse itself (or disorders of the integrity of the connection cord), - at least one of the above-described means will allow you to restore the performance of the manipulator. There were no problems with viruses, since each user should take care of the security first.

Computer mouse is a brilliant device that was created almost in the middle of the last century. Without this simple thing, we could not fully control the computer and the laptop, because it simply does not exist. Therefore, when it ceases to work normally or simply "buggy", it is necessary to somehow solve this problem. Today I will tell you why the mouse may not work and what actions need to be done to reanimate it.

Causes of problems and their decision

• To understand whether the device really does not work or the problem lies in your computer, you need to connect it to another PC or laptop. If the mouse turned out to be completely a worker, then try to insert it into another port on my main computer - it is known that USB ports are often "buggy", and the plug is permuting the result. If you have a PS / 2 mouse, then I recommend to purchase a special PS / 2 / USB adapter, so that you can use the device via any USB port. PS / 2 itself connector can be not working, from here and problems.

• The next step is closely looking at the mouse, in particular, on the LED. If he glows, but at the same time the device does not want to work, then it is for sure in "Softe". First, try simply restart the computer (and do not laugh, it works in very many cases) and if it does not help, then try installing the driver specifically for your device. To do this, go to the manufacturer's official website and download the desired drivers.

• In some cases, the problem may occur after installing this or that is probably in the conflict system, with the result that the mouse ceases to respond to any actions. Often something similar happens when viruses hit the computer. What to do in such situations? It is recommended to download the computer in safe mode and check the performance of the "rodent". If it works, either remove the installed software or roll back the system on an earlier date. And of course, do not forget to scan PC for viruses.

• Interestingly, users PS / 2 mice are often encountered. Why? The fact is that the plug that is used in such devices is not ideal. It consists of a variety of contacts (sort of pins) that have the property bent. For example, you took out the plug from the port and inserted it back, after which the mouse stopped working. Apparently, some pins wondered and need to be returned to their usual position. This can be done, for example, using the most ordinary tweezers or something sharp (you can even come up with the most common ballpoint pen). USB mouse completely devoid of this problem due to a much more thought-out system.

• Theoretically, the wire may be damaged. It happens rarely because it is not subjected to strong mechanical impacts. Nevertheless, pets often tear off the wire. So, carefully examine it on the subject of external damage and if you were not detected, we do the following: take the mouse and start to move the wire. If the indicator (LED) starts blinking at this moment, then, apparently, the case is really in the wire. It must be replaced, although in most cases it will be cheaper to purchase a new "rodent".

• In case you use a wireless mouse, then the most frequent cause of the problem is a served battery, as well as the problem with the Bluetooth receiver driver.

• Now go to buttons and wheels. If we talk about the buttons, the inoperability of one of them or both is most often associated with the mechanical problem. Theoretically, you can overpass the chip, but usually it is economically unprofitable - the new mouse costs the same amount if not cheaper. But if it hits the wheel, that is, it makes sense to disassemble the device and clean it from dirt - hair and other "charms" are wound on the wheel, which interfere with its work. Try to clean the wheel, everything should come back.

• Continuing the conversation about the buttons, it is impossible not to mention that for additional buttons that are located on the sides of the mouse (they are commonly used in games), you need to install other drivers that are included with the device. You can also download them on the manufacturer's website.

• In the event that the mouse still works, but not quite adequately, for example, jumps from side to side, then this can be guilty like dirt (in the case of ball mouses it can be said, normally) and problems with settings. In the first case, it is enough to clean the device from dirt, then in the second you need to play with the settings. For example, try configuring the sensitivity of your gadget. How to do it, I am.

• If problems with inoperability arise in games, or rather, the mouse does not work in a particular position, then the problem is 99% in the settings of the game itself.

What can I do?

• If you have recently purchased a mouse that is under warranty, and she stopped working, then do not try to repair it yourself - this can lead to the loss of warranty obligations.

Sometimes users face a problem when the mouse does not react to clicks. Why can it happen? How is it suggested to deal with the task? What features and nuances ...

One of the most unpleasant problems with the mouse is the problem with the left button. Suddenly she stops responding to clicks.

The click is not registered by the system that is undoubtedly annoying, as it makes it difficult to work - instead of double clicking on the program shortcut, you sometimes need to click 3 or 4 times.

You want to drag something quickly, but it turns out that the left button was not clamped. Of course, the problem can be specifically in the mouse itself, and wearing a purely technical character.

Then most likely it will have to be replaced, since the mouse buttons are practically not repaired. Only the first step in this situation you need to check the mouse on another computer or laptop.

Then you can eliminate or confirm technical defects. If you connect to a friend's computer, and it works correctly, it means that the problem can be your computer. Then it makes no sense to buy a new one - the solution must be sought in the settings of Windows 10, 7 and so on.

The left mouse button does not work - connect it to another USB port

Today, most mice are equipped with a USB port - model with the output of PS2 are very rarely used.

Usually we have on a computer or laptop a lot of USB ports, so switch to another USB input to another step.

It often happens that the USB port may be damaged and cause problems (of course, in the case of a wireless mouse, this step is skipped).

You can switch to another port, not even turning off the computer - just pull the USB plug and connect it to another input.

The left mouse button does not work - check the settings in the Device Manager

If the aforementioned solution did not help, the following source of the problem may be the driver settings responsible for the operation of USB ports.

The system may have a function that, as part of the energy saving, disables or reduces the operation of individual functions of the computer.

There is a possibility that such a reaction occurs in the USB driver, so the system sometimes "breaks" the cliques with the left mouse button.

Go "Task Manager" and find a list of all devices on your laptop or computer.

Expand the USB Controlles tab. You will find parameters such as "Generic USB Hub".

Double-click each of these items and you will open a new power management window.

Uncheck the Allow Computer Disable This Device to save power. Repeat for each element "Universal Controller".

Left Mouse Button does not work - Check the power parameters

The next step will be to configure the power parameters for the active profile. To do this, go to the "Control Panel" and open the "Power".

A new window will appear with a list of preferred and additional plans. One of them will be marked as the one you currently use.

Click next to it to "Changing the Plan Settings", and then in the new window, select "Change Advanced Power Parameters".

Find the USB Settings tab\u003e "Time Turning Off Parameter of the USB Port" and select "Disabled".

The left mouse button does not work - turn off the touchpad delay (only on the laptop)

In Windows 10 there are functions that are useful for users of laptops - it is about the possibility of postpone response to clicks as you enter.

Have you ever written something on a laptop and accidentally touched the touchpad by hand, and the cursor jumped forward?

Touchpad delay is to prevent such situations. When the laptop detects that we are doing something on the keyboard, it causes a delay of clicks.

This option may be unpleasant for playmen who play on laptops using a mouse.

It turns out that in some cases this feature blocks the operation of the mouse buttons connected to USB.

If we play on the laptop, we usually keep your hand on the keyboard all the time - the rest is not required.

The delay function processes the game in the same way as the entry in the text editor, and for a short time blocks the mouse clicks.

Fortunately, you can disable, just how to disable the debugging of the touch panel in Windows 10 will describe later.

And so I read the first article "", the mouse fault is determined.

So we will deal with "", the repair is somewhat more complicated, and we need as a donor, or inoperative, or the cheapest computer mouse, the switches are almost identical.

2. The mouse stopped responding to clicks or does it once, as a rule, the left mouse button, as the most loaded. Himself in the excitement I am not a childish at it, although the result does not depend on the strength of clicking clicking. Here is the microswitch of the mouse and does not withstand, or has exhausted the laid number of clicks. Check. We twist, we will weigh, twist the wire, the cursor comes to life, then the wire is still. The computer mouse is in absolute rest, the wire was recorded, (to exclude the influence, if all the same wires are fluttered), we try to gently click, there are switches, then the switch. Periodic skipping of a computer mouse clicks may not respond at all. So the button does not work.
This mouse fault, is somewhat more complicated, and it will take anyone to repair the mouse (the price does not matter) it will come up and a faulty mouse, as a donor of spare parts, the right button on it will certainly work, well, or sideways.

Do not be surprised if in the same computer mouse, with the form and in the series, there will be a different stuffing, the technology does not stand still. So with interchangeability, problems. That is, one block, it is not necessary to transfer another elementary. If earlier the wires were inserted into the Pope connector, now we have soldered everywhere. On the latter, so in general, the switch is a switch that is half a year old, if you have such about it "How to repair an optical or laser mouse. Sori is still writing"

At the end of the article " Mouse repair, mouse button does not work". We have to draw a drawing, the photo is not, and maybe someone has a simple soldering method. Distracted.
We disassemble the mouse for repair, as written in "".

Disassembled the mouse, enter the board, the screws are all unscrewed

On our mouse, we will have to train without overheating, the switch on it is already broken. Heat the legs of the microspector and, by going with a knife (or pulling his fingers on the reverse side), we disappear it ( we do everything at the same time and quickly).

Pull the switch, at the same time heating legs

Not overheating switch, here you can still make a mistake, we work on the donor as miners without errors.

Tighten the heating legs, then one way

We take any old mouse, compare the switches in height: if the same is easier. If they differ, it means that above, consists of two halves.

If the mouse button is high, remove the spacer

One of which is a spacer. After removing the spacer, the micro-switch will fit instead of yours. On old computer mice, mostly high. Sticking legs on the reverse side of the board, bend (otherwise it does not sit in its place). I only saw the two types of switches, with a spacer and without it, from the switch with a spacer you can make a switch of any height (changing spacers like washers).

We disappear from the old mouse for a hundred rubles a microswitch (carefully! Overheat - it will not work (he plastic). Then disappear the second from the older, in the end, turn out!). And solder it to our "beloved" (no matter how much it costs, you know the habit). When they solder the microswitch, you do not eat a lot of tin, it may interfere on the sole. But not enough, the solder also serves to fix the microswitch, they do not drive the beauty, it is still unallowlessly, (if the switch will break the switch, again you will have to disassemble the mouse)! The switch holds only tin. Not superheated switch, makes a characteristic click, click. We watch photos.

Not very beautiful, but it works

It turned out not very beautiful, but everything works with a bang (this is the second mouse treason). Mouse repair, the mouse button does not work.Now Favorite, well, I hope the wrong (with cheap do not bother) Game rodent with you forever. As I wrote above, all manipulations I once did a simple screwdriver. In Oak Oak Oak. The repaired microswitter is enough for almost a year of active judgment, tested by practice. Yesterday, only a computer mouse in each other crashed, if he worked, there would be no articles. Maybe someone will help. Yes, and also, there is another ma-a-a-linquent malfunction, but about it to a heap in "how to repair an optical or laser mouse", or even so much rolled.

Hope "Mouse repair, the mouse button does not work" And "as well as exotic computing mouse faults, someone will help to revive a computer mouse.

Write comments, I will answer. In the meantime, before the meeting !!!

How to solve the problem with the left and press, which works across

One of the most irritating mouse malfunctions is the problem with its left-click. There is a situation where suddenly no apparent causes the left mouse button or it started responding to user clicks.

Each fourth or fifth click is not perceived by the system, this behavior is very annoying, because it makes it difficult to work on the computer - instead of a double click on the program shortcut, sometimes you need to click 3 or 4 times. This concerns and perform any actions - want to quickly allocate, for example, a group of shortcuts on the desktop, to drag and drop their mouse cursor, but it turns out that the left button does not work. Why doesn't the left button always respond to user clicks?

Of course, the problem may be in the mouse itself and damage is purely technical. The left button is worn and does not always respond to clicks. In this case, it needs to be repaired or buy a new mouse.

But before you do, it is necessary to check whether it works on another computer or - if there is such an opportunity - connect another working mouse to the computer. Thus, you can exclude or confirm its technical malfunction. But if you connect a problem mouse to your friend's computer and it will work correctly, it means that problems with your PC. Then it makes no sense to buy a new mouse - you should look for a solution in the Windows 10 settings.

Step 1: Connect the mouse to another USB port

Look, through which input your mouse is connected to a computer. In most cases, the connection is made through the USB port, but still occasionally there are devices with PS2 connector.

First of all, you need to check the service of the USB port, because it may be damaged and cause problems with work. Connect the mouse to another port, without turning off the computer - it should be determined after a few seconds.

Step 2: Check the settings in Windows Device Manager

If the above method does not work, the fault can be the controller responsible for the operation of USB ports. The system is equipped with a function that, within the framework of the energy-saving mode, turns off or reduces the activity of individual components of the computer. There is a chance that the mode affects the USB driver and therefore Windows 10 sometimes "does not catch" the left-button cliques.

In Windows 10, right-click on the Start button and go to the Device Manager or call it the DevmGMT command. MSC »

Expand USB Controllers. Here you will find such items like "Generic USB Hub" and "root USB-hub". Double mouse click each and go to the "Power Management" section.

Remove the checkbox "Allow shutdown of this device to save energy." Repeat these steps for each element of the USB Controllers.

Step 3: Check the power parameters

The next step is to configure the power supply parameters for the active profile. To do this, go to the Windows 10 control panel and enter the "power settings" in the upper right corner of the "Power Settings" to the search string.

A window will appear with a list of basic and additional plans. One of them will be marked, that is, the one that is used by the system. Click next to it to "Change Plan Settings", and then in a new window, select "Change Advanced Power Parameters".

Find "USB settings - a temporary disabling parameter of the USB port" and select "Forbidden". After check how the device works.

Step 4: Turn off the touchpad delay (in laptops)

Windows 8.1 and 10 are equipped with features useful for laptop users, including the function of slowing the reaction to clicks when entering. Have you ever happened that you have gained text on a laptop and accidentally touched the touch panel with the palm, as a result of which the mouse cursor rearranged?

Touchpad delay serves to prevent such situations. When the laptop detects that you work on the keyboard, then the delay in the click. However, this feature may not be comfortable for players who play on laptops with mouse and that's why.

It turns out that in some cases the function blocks the action of the mouse buttons connected via USB. If you play a laptop, then the hands are usually all the time on the keyboard - the remaining input devices, in the consideration of the system, should not be involved.

The delay function perceives the game just as a set of text, and blocks the mouse clicks for a short period of time, and, unfortunately, periodically (the button works after time). In this case, the laptop delay function can be disabled.

Hello, dear blog readers Website. I do not know if you came across such a problem as dual or triple triggering mouse button in one clickBut definitely - such a problem exists and it is often found at users, as evidenced by numerous records on the forums. What is there to talk, I myself repeatedly witnessed the situation when 2-4 windows immediately opened with one click of the left button, instead of one, it was terribly annoyed and hurt the work. And then I wondered how to fix the mouse without having special tools.

And that's what I managed to find out, they write on different sites that you need to sneak micrik (switch - the button on the board that makes a click) from some non-working mouse, or put the paper \\ isolate under the key and then, they say, the problem will leave. However, there is a way in which the need for a soldering iron and the lining of something disappears, and the time for repairing the mouse will take you no more than 10 minutes. The difficulty is that to implement this method you will have to disassemble the mouse, but the same will need to do with other ways.

The housing of any computer mouse is bonded by screws, some of them can be in such places that when a fluent inspection can be simply not found. Usually, screws are below, they fasten the bottom of the mouse and the rest of it. Carefully remove all the screws visible to the eye, then press the housing - if the bottom holds something else, then you need to find hidden screws, I suggest searching them, for example, under stickers or lining. Be sure to disassemble the mouse, turn it off from the port, in order to avoid any trouble.

There are different types of computer mice - game, office (usual), wireless and so on, but their inner structure is very similar. No matter how many buttons have a mouse, each of them will be their micrik. What is noteworthy, these are identical to the micros, which allows them to be replaced in the event of a breakdown. Even under the scroll wheel there is your own switcher.

The switch itself consists of two parts, the lower part (base) is fastened to the contact pin with the solder, the upper part is the case of the switch that closes the inner part. Inside the switch there is a thin copper plate of a peculiar form when it begins under the action of power - you can hear a click, the same "click", which usually publish all the mouse buttons. The problem lies in the plateBut to get to it you need to remove the switch housing.

It is best to make a thin screwdriver or something else that it will be convenient for you. Carefully find the micric case from the end, then do it all over the perimeter of the switch. Be careful, a small plastic button may fall as a result of the opening (it is red on the image), this is the part for which the effort is transmitted from your pinch to the copper plate. Plate keeps on supportsthat do not allow her to "walk" within the body. However, one of the ends of the plate is not rigidly fixed, so to release the plate, you have to move it a bit aside.

Great, now. The fact is that with time, the metal sends ("tired"), and in a certain position, the plate is descended so close to the bottom contact, which in the share of a second it makes several closures, as a result of which we can observe the multiple opening of windows in Windows when one click, eg. It is necessary to flip the plate, a screwdriver or other item to be slightly bent "tail" up, it is important not to overdo it, otherwise you can break the plate (copper is very thin).

Now you need to put the plate on the mounts, start the installation better than the movable side of the plate. I do not argue, it's not so easy to do, because the item is very small, but with a certain skill everything should turn out. But the installation of the plate in place is only a floor of the case, it is necessary to still install the micrika housing back, it is blessing on the latch. Before installing the case of the switch to the place, insert the white (or any other color) into it from the inside to it so that its narrow part looks up, then you can snap the housing back.

Well, that's all, now it remains only to assemble the mouse back, tightening the screws in the connection places. If you are all done correctly, then you do not have to attract a mouse or run to the store for a new one. And if suddenly the problem with the mouse repeats, now you know what to do. Such a hard way even you can adjust the hardness of clicking, just flexing the plate at the desired distance. Personally, I love when pressing the mouse button is clear and rigid and accompanied by a loud click.

This procedure can be repeated arbitrarily once, until the lower part of Micric falls around, still plastic cannot be called resistant to mechanical damage material. Even as an option - you can completely turn the micrik, for example, with an old but running mouse. But firstly, it will take longer, and secondly, the soldering iron can be at hand at hand along with the solder. In addition, you can try to order such switches from the Internet, and in case of which - rearrange copper plates from there, it will be released much cheaper than buying even the simplest mouse. Thank you.